[GLX] Debug Key Sequences

Post Reply
notipa
Posts: 119
Joined: Wed Jun 24, 2015 11:18 pm

[GLX] Debug Key Sequences

Post by notipa »

Enter the key sequence by holding down the ESC key and pressing the keys after the + in sequence. For example, enter "ESC + 0 0" by holding ESC, press the 0 key twice, then release the ESC key. These should work at any screen.

ESC + 0 0: Show information about last shutdown
ESC + 0 1: Power management debug information
ESC + 1 0: Restore normal status bar
ESC + 1 1: Show debug info in status bar, mode 1 (disabled?)
ESC + 1 2: Show debug info in status bar, mode 2
ESC + 2 1: Show files and folders in filesystem
ESC + 2 2: Show character map
ESC + 2 3: Show installed licenses
ESC + 2 4: Invoke idle shutdown
ESC + 2 5: Invoke low battery shutdown
ESC + 2 6: Show list of installed sensors
ESC + 3 1: Show self-test window (versions, keyboard, LCD, sensors)
ESC + 5 0: Show connected USB devices
ESC + 5 1: Show Flash sectors
ESC + 5 2: Flash Erase Test (erases Flash files)
ESC + 5 4: Dump DebugLog cache to file (where?)
ESC + 5 5: Invoke sleep mode for 5 seconds
ESC + 5 6: Toggle sleep simulation (???)
ESC + 5 7: Simulate USB disk connection
ESC + 5 8: Simulate remote filesystem connection
ESC + 5 9: Disconnect battery test (?, erases RAM and resets clock)
ESC + 6 0: MSP430/AIC28 tests?
ESC + 6 2: Toggle show ISR statistics
ESC + 9 9 9: Reset max idle timer
ESC + . = +: Toggle audio debugging mode
ESC + . = -: Record/play audio file (disabled?)

ESC + 6 0 Values:
  • Enable Output Voltage Sensor
    (Enables sensor GLX PA Voltage)
  • Init for Power Amplifier
  • Measure Voltage
  • Measure Current
    (Enables sensor GLX PA Peak Current under some circumstances)
  • Enable Square Generator
  • Disable Square Generator
  • Enable Output
  • Disable Output
  • Send AIC Amplitude...
  • Send MDAC value...
  • Set DC NCO value...
  • Send Offset value...
  • Send Zero Offset value...
  • Send Command...
  • NCO Prescale...
  • NCO Reverse
  • NCO Auto Reverse...
  • Dump Cal Info...
ESC + 6 0 Values on my GLX, all in base 10 as that is what the system uses:
  • Send AIC Amplitude...
    (range is 0 to 127) 118
  • Send MDAC value...
    (range is 0 to 4095) 0
  • Set DC NCO value...
    (range is 0 to 65536) 0
  • Send Offset value...
    (range is 0 to 4096) 0
  • Send Zero Offset value...
    (range is 0 to 1023) 0
  • Send Command...
    (range is 0 to 255) 0
  • NCO Prescale
    (range is 0 to 65536) 0
  • Dump Cal Info...
    zero=0, ap=0, aic=e199b10
    mdacp=0, mdacm=0, mdacr=0
    odp=0, odm=0, odz=24252206,odr=c1190084
    m:-9v=0, -4.5v=0, 0v=0, 4.5v=0, 9v=0, o:-9v=0,
    -4.5v=0, 0v=0, 4.5v=0, 9v=0
Post Reply